25ft coiled RJ12 cable engineered for mobile fixtures, lifting systems, and vertical racking.
The TrolMaster ECS-10 is a 25-foot coiled RJ12 communication cable designed to maintain a clean, tangle-free connection between TrolMaster Hydro-X controllers and fixtures mounted on lifting systems or movable vertical racking. It ships as a 15-foot coiled center section with 5-foot straight leads on each end for a secure reach without excess slack.
The TrolMaster ECS-10 is a 25-foot (7.62m) coiled RJ12 communication cable purpose-built for the TrolMaster Hydro-X ecosystem. The cable's architecture is straightforward: a 15-foot coiled midsection flanked by 5-foot straight leads on each end. The coiled design stores compactly at rest and extends under tension without bunching or pulling tight against connected devices.
The RJ12 standard — a 6-position, 6-conductor connector — is the communication backbone of the entire TrolMaster Hydro-X platform. Sensors, device stations, lighting adapters, and control modules all connect via this format, making the ECS-10 a direct drop-in for any point in a Hydro-X installation that requires greater cable travel range than the standard included cables provide.
The ECS-10 is the right cable when fixtures or devices need to move. The primary use case is lighting on adjustable lifting systems — when a fixture is raised or lowered, a straight cable binds or goes slack; a coiled cable follows the movement without stress on the connectors. The same logic applies to movable vertical racking setups where fixtures are repositioned between cultivation phases.
Commercial and indoor cannabis and hemp operators running TrolMaster Hydro-X (HCS-1, HCS-2, or HCS-3 Plus) with RJ12-connected lighting adapters (LMA units) or sensors in high-movement zones will find the ECS-10 the correct cable choice over a standard straight extension. It is also useful anywhere a managed loop of cable is preferable to routing a fixed-length straight run.
The coiled format is the defining feature — it allows full extension when needed and retracts on its own, eliminating cable sag and reducing snag risk in active grow environments. With a 25-foot total reach, the ECS-10 handles longer fixture-to-controller spans that standard 16-foot or 4-foot RJ12 cables cannot cover without adding extension sets.
The cable is rated to operate in temperatures from 32°F to 122°F with relative humidity tolerance up to 90%, consistent with the environmental conditions in commercial cultivation spaces. Both ends terminate in standard RJ12 plugs, making the ECS-10 plug-and-play compatible with any device in the TrolMaster Hydro-X line — sensors, device stations, lighting control adapters, and splitter hubs — without any modification or additional hardware.
TrolMaster's Hydro-X platform connects all sensors and control modules through a daisy-chain topology using standard RJ12 cables and Y-splitters or the SPH-1 splitter hub. The ECS-10 inserts into this chain anywhere a standard cable is used — no special configuration required. It is particularly well-suited to the segment between an LMA lighting adapter and a fixture on a lift, where vertical travel demands a cable that can follow the motion.
For facilities using RJ12 cable rolls (ECS-500) for custom runs or the SPH-1 hub for clean home-run wiring, the ECS-10 serves as a flexible last-leg cable from a fixed hub port to a mobile fixture. Order quantity should match the number of independently moving fixture positions in the installation — one ECS-10 per fixture that requires free movement along the Hydro-X communication bus.
| SKU | ECS-10 |
| Brand | TrolMaster |
| Total Length | 25 ft (7.62 m) |
| Coiled Section | 15 ft |
| Straight Leads | 5 ft each end |
| Connector Type | RJ12 (6P6C) both ends |
| Operating Temperature | 32–122°F (0–50°C) |
| Humidity Resistance | ≤90% RH |
| Compatible Systems | TrolMaster Hydro-X HCS-1, HCS-2, HCS-3 Plus and all RJ12-based accessories |
| Primary Application | Lifting systems, movable vertical racking, mobile fixture runs |
The ECS-10's coiled center section allows the cable to extend and retract as fixtures move — on lifting systems or repositionable vertical racks — without pulling tight, going slack, or creating excess cable on the floor. A straight extension cable has a fixed length and cannot accommodate vertical or lateral fixture movement cleanly.
Yes. The ECS-10 uses standard RJ12 (6P6C) connectors on both ends, which is the universal communication connector across the TrolMaster Hydro-X platform — compatible with the HCS-1, HCS-2, and HCS-3 Plus controllers, all LMA lighting adapters, sensors, device stations, Y-splitters, and the SPH-1 splitter hub.
Yes. The Hydro-X system is designed for daisy-chaining via RJ12 cable and Y-splitters. The ECS-10 plugs into any point in that chain and passes the signal through normally. It can also connect from an SPH-1 hub port directly to a mobile fixture without any additional adapters.
The ECS-10 is rated for up to 90% relative humidity and temperatures from 32°F to 122°F, covering the range of most commercial indoor cultivation environments. Note that the RJ12 connectors on the ECS-10 are not IP-rated waterproof — for wet-zone applications, TrolMaster offers separate waterproof connector variants (ECS-3, ECS-5).
One ECS-10 per independently mobile fixture position. If you have 20 fixtures on lifting systems that each need their own free-movement communication run back to an LMA adapter or hub port, you need 20 ECS-10 cables. Fixed, stationary fixtures can use standard straight RJ12 extension sets (ECS-1) instead.
Get operator-direct pricing and availability. We supply licensed commercial cultivators nationwide.
Request a Quote