Required interface between Matrix Dyna fixtures and MC2/MC5 controllers for full dimming and spectrum control.
The Matrix Dyna Control Adapter (SKU 10-010701-067) is the required connection accessory for integrating Matrix Dyna series LED fixtures with a Matrix MC2 or MC5 lighting controller. Without it, multi-channel dimming and spectrum scheduling are unavailable.
The Matrix Dyna Control Adapter is the purpose-built interface component that allows Matrix Dyna series LED fixtures — including the M6 645W and M8 860W 2-channel and 4-channel variants — to communicate with a Matrix MC2 or MC5 lighting controller. It bridges the fixture's dimming and spectrum channels to the controller's output, enabling the 0-10V and RS-485 signals that drive room-level automation.
Without this adapter in place, Dyna fixtures cannot receive dimming commands or spectrum adjustments from a Matrix controller. This is not optional hardware for operators running centralized lighting control — it is a required component of the complete control chain, connecting from the controller out to the first fixture in a daisy-chain run.
Any licensed cannabis or hemp cultivation facility deploying Matrix Dyna series LED fixtures with a Matrix MC2 or MC5 controller will need this adapter. It is the essential link that makes the controller-to-fixture communication possible. If you are building out a new room, retrofitting existing Dyna fixtures for centralized control, or replacing a damaged adapter in an established system, this is the part.
Commercial operations running multiple fixtures in a daisy-chain configuration — up to 80 fixtures per channel via 0-10V or up to 100 per channel via RS-485 on the MC2 — require proper adapter installation on the first fixture in each run. Facilities scaling across multiple rooms or zones will want to stock one adapter per controller-to-fixture connection point.
Matrix Dyna fixtures support spectrum tuning across independent channels — the 2-channel models offer a main (white + red) and supplemental channel, while 4-channel models add independent Deep Red, Far Red, and UV channels. All of that functionality is controller-driven. The Dyna Control Adapter is what makes those channels responsive to the scheduling, dimming, and spectral programs set on the MC2 or MC5.
The MC5 enables independent scheduling and dimming for each spectrum channel with programmable timers and support for separate group control within a single daisy-chain. The MC2 delivers two-channel control with manual dimming and spectrum tuning for smaller room configurations. In both cases, the Dyna Control Adapter is the required starting point for the fixture-side of that connection.
In a standard Matrix Dyna installation, the control chain runs: controller → Dyna Control Adapter → first fixture (via M12 cable) → subsequent fixtures daisy-chained via M12 ports. The adapter handles the signal handoff between the controller's output port (RJ14) and the fixture's M12 input. Without a properly seated adapter, the controller cannot communicate with the fixture chain regardless of how the rest of the cabling is configured.
For operators speccing out a full Matrix Dyna build through HSC, this adapter should be counted once per controller-to-fixture-chain connection — typically one per zone or per controller output port in use. Confirm quantities when finalizing your fixture and controller order so your control infrastructure is complete at first power-on.
| SKU | 10-010701-067 |
| Brand | Matrix |
| Compatible Fixtures | Matrix M Dyna series (2-channel and 4-channel) |
| Compatible Controllers | Matrix MC2, Matrix MC5 |
| Control Signal Types | 0–10V dimming; RS-485 |
| Fixture Capacity (0-10V, per controller channel) | Up to 80 fixtures |
| Fixture Capacity (RS-485, per controller channel) | Up to 100 fixtures |
| Daisy-Chain Connection | RJ14 adapter to M12 cable interface |
| Application | Commercial indoor cannabis and hemp cultivation |
| Category | Supplemental Bars, Cloning & Controls |
Required. Matrix Dyna series fixtures cannot receive dimming commands or multi-channel spectrum control from an MC2 or MC5 controller without this adapter in place. It is not an optional upgrade — it is a mandatory component of the control wiring chain.
One adapter is needed per controller-to-fixture-chain connection point — specifically, at the first fixture in each daisy-chain run. Subsequent fixtures in the chain connect to each other via M12 cables and do not require their own adapter. Plan for one adapter per active controller output port.
The Matrix Dyna Control Adapter is compatible with the Matrix MC2 and Matrix MC5 controllers. Both controllers work exclusively with the Matrix lighting lineup and use this adapter to establish the 0-10V or RS-485 connection to Dyna fixtures.
Yes. The adapter is designed for the Matrix M Dyna series, which includes both the 2-channel variants (M6 645W, M8 860W) and the 4-channel variants. Confirm your specific fixture model with your HSC account rep if you have a mixed-fixture installation.
Request a quote directly from this page. HSC sources Matrix accessories through direct vendor accounts, so pricing is competitive with what you would pay through standard distribution. Include your fixture count and controller model in your request so we can confirm you have everything needed for a complete control installation.
Get operator-direct pricing and availability. We supply licensed commercial cultivators nationwide.
Request a Quote