Wall-mount remote control for Leizig R410a commercial dehumidifiers — operate and monitor without accessing the unit directly.
The Leizig Remote Controller (SKU 30600151) is the factory-matched wired control accessory for R410a-refrigerant Leizig dehumidifiers. If your Leizig unit runs R410a, this is the correct controller — Leizig produces a separate remote for R32 units, and the two are not interchangeable.
This is Leizig's factory remote controller accessory, designed specifically for their R410a-refrigerant dehumidifier models. It gives operators the ability to adjust setpoints and monitor unit status from a fixed wall-mount location — without climbing a ladder, opening a mechanical room, or walking to wherever the unit is installed in the facility.
Leizig offers two distinct remote controllers: one for R410a units (this SKU, 30600151) and one for R32 units. These are not cross-compatible. Before ordering, confirm which refrigerant your Leizig dehumidifier uses — this information is on the unit's nameplate. If you have an R32 unit, contact HSC for the correct part.
Commercial cannabis and hemp cultivation facilities running Leizig dehumidifiers in configurations where direct unit access is inconvenient or impractical. Common scenarios include ceiling-hoisted or wall-mounted units in sealed flowering rooms, units installed in mechanical chases adjacent to the grow space, or any multi-room ducted setup where the dehumidifier serves a room it is not physically located in.
In a ducted configuration, placing the remote controller in the conditioned space — rather than at the unit — means the sensor reads actual grow-room conditions, not conditions at the machine itself. For VPD-sensitive cultivation, that sensor placement difference matters: you are controlling to the environment your canopy is experiencing, not the environment behind a return duct.
Leizig's commercial dehumidifier lineup spans multiple capacity tiers — the LG195, LG228, LG335, LG508, and LG880 — and units within that lineup are available with either R410a or R32 refrigerant. R410a has been the standard refrigerant in commercial dehumidification equipment for many years. R32 is a lower-GWP refrigerant increasingly adopted by manufacturers due to evolving environmental regulations; R32 has a global warming potential of approximately 675 versus R410a's approximately 2,088.
The remote controller's internal control logic and sensor calibration are matched to the refrigerant type of the host unit. Using an R32 controller on an R410a unit — or vice versa — can result in incorrect operation. Always verify the refrigerant type on your unit's data plate before ordering this accessory. This SKU (30600151) is correct for R410a units only.
Leizig builds commercial dehumidifiers specifically for the demands of professional cultivation: galvanized steel chassis with corrosion-resistant surface coatings, MERV-8/13 filtration to capture dust and spores, vibration-dampening construction for continuous 24/7 duty cycles, and operation below 73 dB(A) across the lineup. Every Leizig model from the LG195 through the LG880 includes RS485 (MODBUS) communication and remote dry contact input for integration with environmental controllers.
The remote controller accessory complements that integration story: it adds a dedicated human interface point in the grow space, so operators can monitor and adjust humidity targets without interrupting controller automation or making changes at the unit itself. For facilities that run Leizig dehumidifiers under environmental controller automation, the wired remote provides a secondary operator-level interface that does not disrupt programmed setpoints unless deliberately changed.
| HSC SKU | 30600151 |
| Manufacturer | Leizig |
| Accessory Type | Wired remote controller |
| Refrigerant Compatibility | R410a (not compatible with R32 units) |
| Compatible Equipment | Leizig R410a commercial dehumidifiers (LG series) |
| Installation | Wall-mount |
| Site Category | Climate & Air Quality / Dehumidifiers |
Check the data nameplate affixed to your unit — it will list the refrigerant type. If you no longer have documentation, the nameplate is the authoritative source. This remote (SKU 30600151) is for R410a units only. Contact HSC if you need the R32 version.
No. This is a Leizig-specific accessory engineered to communicate with Leizig R410a dehumidifier models. It is not a universal aftermarket controller and will not function correctly with other brands or with Leizig's R32-refrigerant units.
It allows you to start and stop the dehumidifier, adjust humidity setpoints, and monitor ambient conditions from a wall-mounted location in the grow space — without accessing the unit directly. In ducted installations, positioning the controller's sensor in the conditioned room gives you a more accurate read of actual grow-room humidity than the sensor at the unit itself.
MODBUS integration is for connecting to an environmental control system (e.g., a room-level climate controller). The wired remote controller is a separate operator interface — a dedicated display and control panel for manual oversight and adjustment. Facilities that use both typically let the environmental controller handle automation and use the remote for spot-checking and manual overrides without navigating controller software.
HSC supplies Leizig accessories nationally to licensed cannabis and hemp operators. Click 'Request a Quote' or contact us directly — we'll confirm availability, lead time, and pricing for your account.
Get operator-direct pricing and availability. We supply licensed commercial cultivators nationwide.
Request a Quote