OEM-matched 120V supply cord with right-angle M19 connector for Flexstar LED fixtures.
The Flexstar 120V 10ft Right-Angle M19 Power Cord (SKU 10-010704-354) is the manufacturer-matched power supply cord for Flexstar LED grow light fixtures that use the M19 circular connector. Match this cord to your 120V service circuits — confirm your fixture's connector type and service voltage before ordering.
This is the OEM power cord supplied by Flexstar for LED grow light fixtures that terminate in an M19 circular connector. The M19 is a locking circular connector format used across Flexstar's commercial fixture lineup to connect the power supply enclosure to the AC mains. The right-angle connector body means the cord exits parallel to the fixture housing rather than straight out — a practical advantage in overhead or rack-mount installations where a straight connector would conflict with adjacent fixtures, cable trays, or the ceiling structure above.
The cord is rated for 120V AC service, making it the correct choice for facilities running their Flexstar fixtures on standard 120V branch circuits. Flexstar fixtures that accept multiple input voltages (120V, 208V, 240V, 277V) will have a corresponding cord SKU for each voltage tier. This listing covers the 120V variant only. Do not use this cord on 208V, 240V, or 277V circuits.
Licensed cannabis and hemp cultivation operators running Flexstar LED fixtures on 120V branch circuits are the primary buyers of this cord. Common use cases include replacement of a damaged or missing OEM cord, initial fit-out of a new grow room where additional cord length is needed to reach the nearest panel outlet, or facilities that have repositioned fixtures and need a fresh cord to accommodate the new layout.
Facilities spec'ing Flexstar fixtures for a new build should confirm the service voltage at each circuit before ordering power cords. If your electrical design calls for 120V single-phase circuits for your Flexstar fixtures, this is the correct cord SKU. Operators on 208V, 240V, or 277V service should reference the corresponding Flexstar cord SKU for their voltage tier to avoid a mismatch.
In commercial cultivation environments — vertical racks, single-tier rooms with dense fixture spacing, or greenhouse truss installations — cable management directly affects safety and serviceability. A straight M19 connector body projects perpendicularly from the fixture port, which can create clearance conflicts with neighboring fixtures or overhead structure and puts mechanical stress on the connector junction when the cord is routed sideways.
The right-angle body on this cord redirects the cable exit to run parallel with the fixture plane immediately at the connector, eliminating that lateral stress point and allowing tighter routing along a cable tray or wire management channel. In a room with multiple Flexstar fixtures on a common power distribution run, right-angle cords produce a cleaner, more serviceable installation than straight-body alternatives and reduce the risk of connector wear from repeated repositioning of overhead fixtures.
Before ordering, verify two things: (1) your Flexstar fixture uses an M19 circular connector at its power input port, and (2) your branch circuits are 120V. Flexstar's commercial LED lineup — including the 645W, 800W, and 1000W Pro-series fixtures — uses M19 connectors between the fixture and its power supply enclosure. The user manual for your specific fixture will identify the connector type and confirm the appropriate power cord SKU.
This cord is a Flexstar OEM accessory, supplied through HSC's direct account with Flexstar. It is intended for indoor, climate-controlled cultivation environments only. Keep cords clear of standing water, irrigation lines, and any surface that routinely exceeds ambient grow room temperatures. Connect and disconnect only when the fixture is de-energized — Flexstar's own installation documentation specifies not to connect or disconnect fixtures under load.
| SKU | 10-010704-354 |
| Brand | Flexstar |
| Rated Voltage | 120V AC |
| Cord Length | 10 ft (approx. 3 m) |
| Fixture Connector Type | M19 circular (right-angle body) |
| Wall Plug | NEMA 5-15P (standard 3-prong, 120V US) |
| Conductor | 3-wire grounded |
| Intended Use | Indoor cultivation environments only |
| Compatible Fixtures | Flexstar LED fixtures with M19 power input connector |
| Voltage Compatibility Note | 120V only — separate SKUs available for 208V, 240V, 277V |
Check the power input port on your fixture's driver or power supply enclosure. The M19 is a circular locking connector approximately 19mm in diameter. Your fixture's user manual will identify the connector type and list the correct power cord SKU for each supported voltage. If you're unsure, reach out to HSC and we can cross-reference your fixture model.
No. This cord is rated for 120V service only. Using a 120V-rated cord on higher-voltage circuits is a safety and equipment hazard. Flexstar offers separate power cord SKUs for 208V, 240V, and 277V service. Match the cord to your actual branch circuit voltage before installation.
A right-angle connector body exits the fixture port parallel to the fixture plane rather than projecting straight out. In tight rack or overhead installations, this eliminates clearance conflicts with adjacent fixtures and reduces mechanical stress on the connector junction when cords are routed laterally along cable trays. It also produces a cleaner cable run in rooms with multiple fixtures on a common distribution line.
In most single-tier and vertical rack installations where the distribution panel or power strip is mounted in the same bay or row, 10 feet is sufficient. If your nearest outlet or distribution point is significantly farther than 10 feet from the fixture, contact HSC to discuss whether a longer cord or a different routing solution is appropriate for your room layout.
Yes — always de-energize the circuit before connecting or disconnecting any M19 power cord. Flexstar's own installation documentation explicitly states not to connect or disconnect the fixture while it is under load. Switch off the breaker or disconnect the circuit, then swap the cord.
Get operator-direct pricing and availability. We supply licensed commercial cultivators nationwide.
Request a Quote