Mount Faven under-canopy bars to your existing bench — no proprietary stand required.
Faven DIY Stand Clips (SKU 10-020209-040) are the metal hardware designed by Faven for operators who want to integrate R6 or R8 under-canopy bars into their existing bench infrastructure — rolling benches, unistrut, or custom fabricated structures — without purchasing Faven's own stand assemblies. All mounting hardware is included.
Faven includes metal mounting clips with every R6 and R8 fixture specifically to give operators flexibility in how they support the bars. This SKU — 10-020209-040 — is the standalone clip set for facilities that need additional clips, are building out a large run of benches, or are integrating the bars after the initial fixture purchase. The clips allow the bar to be secured directly to an existing structural surface rather than relying on Faven's adjustable stand product.
Common attachment points include unistrut channel, rolling bench frames, custom-welded bench tube, or inverted container rims. The clip-and-screw approach keeps the bar low-profile and locked in position through routine IPM activity, wet-downs, and the general traffic of a commercial grow floor — all without adding stand hardware between the substrate surface and the light bar.
Operators who already run rolling bench infrastructure — or who fabricate their own bench systems — typically don't want to stack Faven's pre-made stands on top of an existing frame. The DIY clips let the grower determine mounting height and angle based on their specific bench geometry, plant height at harvest, and canopy architecture, rather than being constrained to the 8"/10"/12" increments of the adjustable stand.
Cultivators growing plants over five feet tall often need to position under-canopy bars higher in the canopy — common target heights run from 15 to 18 inches above the substrate — and the clips allow that position to be achieved using whatever structural material is already in the room. The result is a cleaner bench footprint, no additional stand hardware to clean or move during room turns, and full control over light placement geometry.
These clips are purpose-built for the Faven R Series — the R6 (60% red, designed for HPS top-light rooms) and R8 (80% red, designed for LED top-light rooms and greenhouses). Both bars are IP66-rated with sealed housing, meaning they can handle IPM sprays and wet cleaning procedures without corrosion or ingress issues at the clip attachment points.
The Faven under-canopy system is designed to daisy-chain up to 20 bars per power feed, with bars spaced at 46-inch intervals per row. The clips are compatible with that layout regardless of whether the bench uses rolling or static infrastructure. For facilities that need Faven's own adjustable stands, those are a separate SKU. For everything else — unistrut, welded bench frame, custom fab — these clips handle the mounting.
When spec'ing a full bench run, account for two clips per bar (one at each end of the 46-inch bar length). If your bench structure uses unistrut, standard unistrut hardware pairs with the Faven clips for a clean, tool-accessible installation. If you're screwing into tube or plate steel, pre-drill pilot holes before seating the clips to prevent thread stripping under the weight and vibration of a production environment.
Faven's under-canopy system is DLC-listed on the fixture side, which qualifies participating installations for utility rebate programs where applicable. The clips themselves are a mounting accessory and do not carry a separate DLC listing. Contact HSC for quantity break pricing on clip sets when building out multi-bench or multi-room installations alongside R6 or R8 fixture orders.
| SKU | 10-020209-040 |
| Brand | Faven |
| Compatible Fixtures | Faven R6, Faven R8 |
| Material | Metal |
| Hardware | All mounting hardware included |
| Mount Targets | Unistrut, bench frame, custom fabricated structure |
| Purpose | DIY stand build — attaches under-canopy bar to existing bench infrastructure instead of Faven's proprietary stand |
| Catalog Category | Accessories / Lighting & Cultivation |
Faven's adjustable stands are pre-made metal assemblies that sit on the bench surface and hold the bar at 8", 10", or 12" heights. The DIY clips are mounting hardware that let you attach the bar directly to an existing structural surface — rolling bench frame, unistrut, custom steel — at whatever height your build requires. If you already have bench infrastructure and want to integrate the bars into it rather than stack stands on top, the clips are the right accessory.
Two clips per bar — one at each end of the 46-inch R6 or R8 bar. Order one clip set per fixture in your installation.
Yes. Faven specifically calls out unistrut as a confirmed DIY mounting target for these clips. Standard unistrut channel hardware pairs with the Faven clip for a clean, adjustable-height installation.
Faven ships metal clips with every R6 and R8 fixture as part of the standard package. This standalone SKU (10-020209-040) is for operators who need additional clip sets — for example, when adding bars to an existing installation, replacing hardware, or ordering clips separately from a larger facility buildout.
Yes — that's the primary use case. Faven's own stands top out at 12 inches. For cultivators running taller plants who need bar placement at 15 to 18 inches or higher into the canopy, the DIY clip method using unistrut or a custom-height bracket is the recommended approach. The clips support the bar securely regardless of mounting height.
Get operator-direct pricing and availability. We supply licensed commercial cultivators nationwide.
Request a Quote